Search Results

Electronic braking system (EBS) of commercial vehicle is developed from ABS to enhance the brake performance. Based on the early development of controller hardware, this paper starts with an analysis of the definition of EBS. It aims at the software design of electronic control unit, and makes it compiled into the controller in the form of C language by the in-depth study about control strategy of EBS in different braking conditions. Designed controller software is divided into two layers. The upper control strategy includes the recognition algorithm of driver's braking intention, estimation algorithm of the vehicle state, conventional braking strategy which consists of the algorithm of deceleration control and braking force distribution, and emergency braking strategy which consists of the algorithm of brake assist control and ABS control.

The hybrid electric city bus, which consists of the electric motor and battery, is obviously different from the traditional buses. This paper focuses on optimizing the characteristics of the automatic mechanical transmission in hybrid electric city bus and does the following studies: firstly, in order to reduce the fuel consumption, the transmission ratio and some structural parameters are optimized with CRUISE software; secondly, the volume and weight of the transmission structure is reduced and optimized by numerical optimization approach, with the limitation of the structural reliability.

The simulation of electro-pneumatic components used in brake systems of commercial vehicles is of great importance in order to understand their characteristics for developing a control logic and improve the braking performance. As the goal of improving the performance of the commercial vehicle pneumatic EBS(Electronically controlled Braking System), static and dynamic characteristics of proportional relay valve for commercial vehicle pneumatic EBS have been simulated by using MATLAB/Simulink environment and validated by testing on hardware-in-the-loop test bench focused on its pressure hysteresis characteristic. The simulation and test results show that the mathematic model for proportional relay valve characteristics is reasonable and reliable, and this simulation tool can be used for research and developing of pneumatic EBS system for commercial vehicle effectively.

A new road feel feedback control design of steer-by-wire (SBW) is proposed, which is produce the steering feel of conventional vehicle with equipped electronic power steering (EPS) system, due to SBW system removes mechanical linkages between steering system and front wheels. A dynamic model is established to study the road feel generation and deal with the need of computed rack force of steer system. Based on the analysis of the assisting characteristic and the active damping control strategy of the EPS system, an integrated road feel algorithm is proposed. For rack force is difficult to measure, an estimator is presented to estimate rack force by Kalman filter (KF). The hardware-in-the-loop simulation (HILS) test bench results show that the proposed road feel control design make drivers get road feel information and SBW system can improve the vehicle maneuverability and comfortably.

In order to accurately characterize the dynamic characteristics of articulated heavy vehicles, 3-dof (degree of freedom) model and 5-dof simplified model of articulated heavy vehicle are established and key parameters of models are identified by the method which is to combine double models with genetic algorithm and by using Trucksim data. Simulation study, which combines 5-dof simplified model with the MAPs of key identified parameters, is carried out. Comparison, which is between simulation results and Trucksim data, indicates that the key parameters of simplified model can be accurately identified, the MAPs of key identified parameters can satisfy the demand of characterizing the actual state of vehicle and lay a foundation for vehicle stability control.

A fault detection and diagnosis (FDD) algorithm of 4WID/4WIS Electric Vehicles has been proposed in this study aiming to find the actuator faults. The 4WID/4WIS EV is one of the promising architectures for electric vehicle designs which is driven independently by four in-wheel motors and steered independently by four steering motors. The 4WID/4WIS EVs have many potential abilities in advanced vehicle control technologies, but diagnosis and accommodation of the actuator faults becomes a significant issue. The proposed FDD approach is an important part of the active fault tolerant control (AFTC) algorithm. The main objective of the FDD approach is to monitor vehicle states, find the faulty driving motor and then feedback fault information to the controller which would adopt appropriate control laws to accommodate the post-fault vehicle control system.

The passive fault-tolerant performance of the integrated vehicle controller (IVC) applied on 4WID/4WIS Electric Vehicles has been investigated in this study. The 4WID/4WIS EV is driven independently by four in-wheel motors and steered independently by four steering motors. Thanks to increased control flexibility of the over-actuated architecture, Control Allocation (CA) can be applied to control the 4WID/4WIS EVs so as to improve the handling and stability. Another benefit of the over-actuated architecture is that the 4WID/4WIS Electric Vehicle has sufficient redundant actuators to fight against the safety critical situation when one or more actuators fail.

Impact torque will be generated on the steering wheel when one tire suddenly blows out on high way, which may cause driver's psychological stress and result in driver's certain misoperations on the car. In this paper, the model of tire blowout vehicle was established; the tire blowout was detected based on the change rate of tire pressure, meanwhile, the rack force caused by tire blowout was estimated through a reduce observer; finally the compensation current was figured out to reduce the impact torque on the steering wheel. Results of simulation tests showed that the control strategy proposed in this paper can effectively reduce the impact torque on the steering wheel and reduce the driver's discomfort caused by tire blowout.

A fault tolerant control (FTC) approach based on reconfigurable control allocation for four-wheel independently driven and steered (4WID/4WIS) electric vehicles against driving motor failures is proposed in order to improve vehicle safety, performance and maneuverability after the driving motor failures. The proposed fault tolerant control method consists of the following three parts: 1) a fault detection and diagnosis (FDD) module that monitors vehicle driving condition, detects and diagnoses actuator failures; 2) a motion controller that computes the generalized forces/moments to track the desired vehicle motion using model predictive control method; 3) a reconfigurable control allocator that optimally distributes the generalized forces/moments to four wheels aiming at minimizing the total tire usage. The FTC approach is based on the reconfigurable control allocation which reallocates the generalized forces/moments among healthy actuators once the actuator failures is detected.

In order to improve the braking energy recovery, a parallel hybrid electric bus simulation model with electric braking system (EBS) was established by co-simulation platform for the TruckSim and Matlab/Simulink in this paper. EBS makes the front and rear shaft braking force arbitrarily distributed, which is more effective to improve the rate of energy recovery and the braking stability. A braking force distribution algorithm for hybrid electric bus based on EBS was designed in this paper. Under the premise to meet the driver's needs and the ECE regulations, this braking force distribution method focuses on making the braking force distribute to the drive shaft to a maximum extent, so as to obtain the maximum energy recovery rate by the utilization of the motor regenerative braking. At last, the simulation in different operating conditions was used to analyze the braking energy utilization and the braking performance based on the simulation model.

Steering-By-Wire (SBW) system has advantages of advanced vehicle control system, which has no mechanical linkage to control the steering wheel and front wheels. It is possible to control the steering wheel actuator and front wheels actuator steering independently. The goal of this paper is to use a joystick to substitute the conventional steering wheel with typical vehicle SBW system and to study a variable steering ratio design method. A 2-DOF vehicle dynamic reference model is built and focused on the vehicle steering performance of drivers control joystick. By verifying the results with a hardware-in-the-loop simulation test bench, it shows this proposed strategy can improve vehicle maneuverability and comfort.

The paper describes an algorithm, which estimates the mass of large buses and axle load distribution using pedal position, wheel speed and the wheel cylinder pressure sensors. This algorithm is allowed to achieve the purpose without additional sensors by using the rotational speed sensors from ABS system and air pressure sensors in brake cylinders form ESP system. The axle load distribution algorithm mainly consists of three steps. Firstly, deceleration of the bus is estimated and then the mass of the bus is estimated. After that, the position of the mass centre is estimated. Taking account of the tire nonlinear characteristics under longitudinal forces and vertical forces, mass estimation, deceleration and the position of the mass centre of buses is corrected by the coefficient, which is determined by the wheel cylinder pressure, the wheel speed and mass estimation.

The EPS motor will be over-heated if large current lasts for a long time, which will decline the performance of EPS motor and even lead to irreparable damage. So the over-temperature protection control should be conducted in order to protect the components of EPS system, especially the durability of EPS motor. In this paper, the motor temperature was estimated according to the environmental temperature and the current of motor armature, and then the EPS assist current was limited based on the estimated temperature of motor to ensure that the EPS motor had a good working condition. So the over-temperature protection control for motor can be realized without increasing the EPS system components. Finally the control strategy for over-temperature protection was conducted in a vehicle with EPS system and its performance was verified.

The quality of the brake system is a significant safety factor in commercial vehicles on the roads. With the development of automobile technology, the single function ABS system didn't meet active safety requirements of the user. The Electronically Controlled Brake System (EBS) system will replace the ABS system to become the standard safety equipment of commercial vehicles in the near future. EBS can be said an enhanced ABS system, it contains load sensor, brake valve sensor and pressure sensor of chamber, etc, and it is more advantages than ABS. This paper describes a flexible integrated test bench for ABS/EBS Electronic Control Unit (ECU) based on Hardware-In-the-Loop (HIL) simulation technique. It consists of most commercial vehicle pneumatic braking system components (from brake pedal valve, brake caliper to brake chambers), and uses the dSPACE real-time simulation system to communicate to the hardware I/O interface.

Vehicle model plays an important role during the development process of a new car chassis. There are 2 different ways to set up the vehicle mathematics model, one is set up based on understanding the system mechanism and the other is based on system identification technique. In this paper, the transfer functions of the vehicle at 100 km/h, including yaw rate to the steering angle and lateral acceleration to the steering angle, were identified. And then the transfer functions under other forward speed were derived through studying two degrees of freedom vehicle model equation. At last the identified model at different speed was used to analysis the stability of closed loop system from the classical control theory viewpoint.

An integrated control strategy for vehicle active suspension system which combines linear quadratic optimum control law with fuzzy control algorithm is designed to improve both ride and handling. The performance of this control strategy is then examined and assessed in an open-loop J-turn driving scenario on a random-rough road by means of computer simulation. Comparisons to a passive suspension system in terms of vehicle sprung mass vertical acceleration, body roll angle and yaw rate is conducted. Simulation results indicate that the integrated control strategy proposed in this paper could effectively enhance vehicle ride comfort meanwhile benefit handling quality and driving safety.

This paper introduces the characteristics of the 4 wheel independent driving/4 wheel independent steering (4WID/4WIS) electric vehicle (EV). Models of Subsystems and the vehicle are constructed based on Matlab/simulink. The vehicle model allows the inputs of different drive torques and steer angles of four wheels. The dynamic characteristics of drive motors and steer motors are considered, and also it can reflect the vehicle longitudinal dynamics change due to the increase of the mass and inertia of the four wheels. Besides, drive mode selection function that is unique to this type vehicle is involved. Simulations and analyses of crab, oblique driving and zero radius turning which are the special conditions of 4WID/4WIS EV are conducted. The results show that the model can reflect the dynamic response characteristics. The model can be used to the simulation analyses of handling, stability, energy saving and control strategies verification of 4WID/4WIS EVs.

This paper sets up a simplified dynamic model for simulating the yaw/roll stability of heavy tractor-semitrailer using Matlab/Simulink. A linear quadratic regulator (LQR) based on partial-state feedback controller is used to optimize the roll stability of the vehicle. The control objective for optimizing roll stability is to be reducing the lateral load transfer rate while keeping the suspension angle less than the maximum allowable angle. The simulation result shows that the LQR controller is effective in the active roll stability control of the heavy tractor-semitrailer.

The research of driver behavior characteristics has been a focus of vehicle handling and stability performance. With the driver preview effort, many different driver preview models of direction control have been proposed and the simulations of driver-vehicle-road closed-loop system made. But in the simulation, most of the conventional models have the same precondition that the road was simply described as a pre-given preview course. How to simulate the driver dynamically deciding vehicle preview course based on the real road circumstance is the key to the further research of the driver model. In this paper, a new driver direction control model is established, which is called the Optimal Preview Lateral Acceleration (OPLA) Model and divided into three sub-models: driver’s information identification model, driver’s fuzzy decision model of vehicle preview course and driver’s performance first-order correction model.